Vagina shrinking ball female dumbbell masturbator smart ball shrinking ball exercise silicone compact adult products Koro ball

Vagina shrinking ball female dumbbell masturbator smart ball shrinking ball exercise silicone compact adult products Koro ball
  • Продавецparscms.net
  • Список ценUS $28.99piece
  • Продажная ценаUS $28.99piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,6 (247)

Oписание продукта

dianxiaobao_1

dianxiaobao_2

 

aeProduct.getSubject()

 

 

1 X 2.2KW Air Cooled Spindle ER25  220V ceramic ball bearings

 

 

aeProduct.getSubject()

_01

 

Basic parameters :  

 

  • Size: 180x80x92mm   

  • Speed Ways: Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.

  • Cooling: Air cooling

  • Power Interface: Optional waterproof air plug. The air plug marked "1 ","2"," 3"," 4", "1 ","2 ","3" were connected to inverter (U, V, W), 4 connected inverter ground. (Pay attention! our spindle "4" connecting to GND,promised personal safety!!)

  • Power: 2.2kw (1HP=0.735w)

  • Voltage: 220v (If you need 380v spindle ,please leave message to us,thank you)

  • Current: 8.5A

  • Frequency: 0-300Hz

  • Speed: 0-18000rpm

  • Runout Off: Less than 0.01mm

  • Bearing type: 2x7007C P4 DB ( Ceramic ball bearings ) & 2x7002C P4 DT

  • Collet: ER25

  • Clip Knifediameter: 1mm,2mm,3mm,3.175mm(1/8),4mm,5mm,6mm,6.35mm(1/4),7mm, 8mm,9mm,10mm,11mm,12mm,12.7mm(1/2),13mm,14mm,15mm,16mm

  • Grease Lubrication 

  •  Main Application:  Engrave for wood,bamboo,normal PCB,PVC,PMMA,plastic,duotone board(ABS)and etc nonmetal, also can engrave on gold,silver,copper, aluminium,Pb etc soft metal surface working.(Please pay more attention, this is wood working spindle, only can used for wood working and aluminum working,please don\'t use it for steel. If you need steel working,please check the metal spindle,thank you!)

_02_03_04_05

_06

 

 

Structural features :

 

  • High-speed electric main bearings used in all C class high-speed angular contact ball bearings, axial pre-load feature, improved support stiffness and live spindle grinding accuracy under high-speed rotation. 

  • Spindle speed according to different uses can be high-speed grease and oil mist lubrication two ways. 

  • Spindle speed rotation temperature rise caused by the use of coolant circulation system eliminated.

 

Prepartions before use:

 

  • Spindle working environment temperature is usually -10 ~ 40 .
  • Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.

 

 

Use correctly:

 

  • Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter\'s specifications and parameter settings need match spindles parameter.

  • Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.

  • It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.

 

 

Care and maintenance :

 

  • Spindle frequency power supply connected rated voltage, frequency should be consistent with the technical parameters of the electro-spindle, spindle speed can be adjusted to change the frequency, and voltage is proportional to the change. 

  • Spindle being not used, the application of compressed air to blow the pipes static coolant.To prevent rust, clogging water holes. Spindle appearance should be oiled. Plus the shaft protection device, put in a dry place. 

  • To replace the spindle bearings, certain professional and technical personnel should be replaced.Supporting special tools, bearings should be replaced fully cleaned without removing the stator coils.

_09

 

 

 

 

 

 

 

 

 

 

 

 

 

   Shipping terms   

 

Our products are sold worldwide.

But if your country is more difficult to transport goods, please contact us in advance to confirm shipping cost.

 

 

    Payment   

 

We accept paypal credit, bank transfer, western union etc. 

Payment must be made within 7days calendar days of the auction end time.

 

 

   Problems And Feedback   

PLEASE DON\'T leave any negative feedback before you contact us.

Please give us the opportunity to resolve any problem,we will try our best to help you.

Your satisfaction is very important for our store, so please contact us before you want to leave a negative feedback. 

Thanks very much in advance.

 

 

   Refund   

 

If you are not satisfied with our package like the products is damage,
please do not sign it and contact us immediately.

If it is possible, please take some photos or make a small video about it. It will help us to solve the problems.

 

 

   Note   

 

We can produce the product according to our customer\'s design. 

If you need something is very special, please contact us about it.

We are willing to help you about it.

 

 

 

 

 

dianxiaobao_3

 

dianxiaobao_4